one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 1 of 10 4g25n rev. f001 ec 9526a general description the ec9526a battery protection ic is designed to protect lithium - ion / polymer battery from damage or degrading the lifetime due to over current for one - cell lithium - ion / polymer battery powered systems. such as cellular phones the ul tra - small package and less required external components make it ideal to integrate the ec9526a into the limited space of battery pack. the accurate 50mv overcharging detection voltage ensures safe and full utilization charging. the very low standby curre nt drains little current from the cell while in storage features high - accuracy voltage detection circuit overcharge detection voltage 3.6v to 4.4v accuracy 50mv overcharge release voltage 3.6v to 4.4v accuracy 50mv overdischarge detection voltage 2. 0v to 3.0v accuracy 100mv overdischarge release voltage 2.0v to 3.4v accuracy 100mv discharge overcurrent detection voltage 0.05v to 0.3v accuracy 30mv load short - circuiting detection voltage 1.1v accuracy 200mv detection delay times are generated by an internal circuit (external capacitors are unnecessary) overcharge detection delay time typical. 100ms overdischarge detection delay time typical. 100ms discharge overcurrent detection delay time typical. 10ms load short - circuiting detection delay time typical 450s high voltage tolerance is used for charger connection pins, vm and co pins are absolute maximum rating 28v 0v battery charge function available wide operation temperature range - 40 ~ +85 low current consumption operation mode typ. 2 .4 a / max. 6.0 a (25 ) standby mode green - mode max. 0.1 a (25 ) self - recovery function max. 3.0 a (25 ) small package sot 23 - 6l lead - free / green product
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 2 of 10 4g25n rev. f001 ec 9526a applications protection ic for one - cell lithium - ion lithium - polymer rechargeable battery packs block diagram o rdering information package part number marking markin g information sot 23 - 6 l EC9526ANB3R 9526a lllll lllll lot no
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 3 of 10 4g25n rev. f001 ec 9526a absolute maximum ratings (vss=0v ta=25 unless otherwise specified) remarks: any operation condition exceeds the absolute maximum ratings will damage the ic. product name list symbol rating unit input voltage between v dd and v ss v dd v ss = - 0.3 ~ v ss = +12 v vm pin input voltage v m v dd - 28 ~ v dd + 0.3 v do pin output voltage v do v ss - 0.3 ~ v dd + 0.3 v co pin output voltage v co v dd - 28 ~ v dd + 0.3 v electrical static discharge hbm 2 kv mm 200 v operating temperatu re range t opr - 40 ~ + 85 storage temperature range t stg - 55 ~ + 125 product over charge detection voltage [v det1 ] over charge release voltage [v rel1 ] over discharge detection voltage [v det2 ] over discharge release voltage [v rel2 ] discharge overcurrent detection voltage [v det3 ] 0v battery charge function mode selection ec9526a nb3r 4.3v 0.0 50v 4.1v 0.0 50v 2.4v 0. 100v 3.0v 0. 100v 140mv 3 0mv available auto - recovery
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 4 of 10 4g25n rev. f001 ec 9526a electrical characteristics (ta = 25 unless otherwise specified) detection voltage
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 5 of 10 4g25n rev. f001 ec 9526a electrical characteristics (ta = 25 unless otherwise specified) delay time pin configuration package pin no. symbol description 1 do over - discharge mosfet gate control terminal 2 vm inpu t terminal connect to charger and system ground 3 co over - charge mosfet gate control terminal 4 nc no connection 5 vdd battery positive terminal 6 vss battery negative terminal
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 6 of 10 4g25n rev. f001 ec 9526a type application circuit *1 r1 is a single \ stage r c filter the higher resistance of r1 the better the filtering effect if th e r1 resistance higher than the recommended value it will affect the internal detection circuit and the voltage detection accuracy will out of specification. we suggest using the reco mmended resistance in application. *2 the absolute maximum rating of co and vm is 28v, customer could choose 20v or 30v dual n \ mosf et switches for different application. *3 add a c1 capacitor between vdd and vss could filter conduction and radiation noise. *4 r2 resistor could have a current limit function and limit charger current surge. discrete components function min. ty p. max. unit remarks r1 resistor current limit noise filtering -- 100 1k *1 r2 resistor current limit esd protection 300 1k 2k *4 r3 thermistor temp. protection -- -- 00 k c1 capacitor noise filtering 0.022 0.1 1.0 uf *3 m1 n - mosfet discharge switch *2 m2 n - mosfet charge switch *2
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 7 of 10 4g25n rev. f001 ec 9526a normal operation the ec9526a monitors the v dd power supply voltage relative to v ss detecting the over - charge and over - discharge conditions. it also monitors the vm voltage to detect the discharge over - current and load short circuiting to protect the battery cell. in normal operation, the v dd should be in the range from the over - charge detection voltage vdet1 to the over - discharge voltage vdet2, and the vm pin voltag e is in the range from discharge over - current voltage vdet3 to charger detection voltage v cha . in normal condition, the internal pull - up resistor from vm pin to vdd r vmd is disconnected and the internal pull - down resistor r vms from vm pin to vss is also disconnected. notice: discharging may not be enacted when the batt ery is first time connected. to regain normal status, vm and vss terminal must be shorted or the charger must be connected. over - charge condition when the battery voltage is greater than over - charge voltage vdet1 and have a tvdet1 time duration from a normal operation condition, the over - charge condition hold and the co pin will output from logic h to logic l to disconnect the battery charging path. it will turn - off the external mosfet and the charging status stopped. it will release the over - charge condition in the following conditions. if the battery voltage less than vrel1 from the over - charge condition, the co will output logic h to turn on the external mosfet to resume the charging path. in the over - charge condition, the discharge over - current and load short circuiting function will be disabled until the batt ery voltage falls below the overcharge detection voltage. it is because that the internal resistance of battery which will trigger the discharge over - current and load short circuiting function in the time when over - charge condition enabled. in over - charge condition, the internal pull - up resistor from vm pin to vdd r vmd is disconnected and the internal pull - down resistor r vms from vm pin to vss is also disconnected. over - discharge condition the ec9526a single - cell lithium protect ic monitors the vdd voltage to detect the over - discharge state from normal operation condition. if the vdd voltage becomes lower than the vdet2 and continues for the over - discharge delay time tvdet2 from normal operation condition, the do pin will output l to disable the external mosfet and the discharging stopped. if a charger is connected and the vdd voltage is greater than over - discharge release voltage vrel2, the over - discharge condition released. in over - discharge condition, the charging path is connected by the parasitic diod e of discharge controlled mosfet. when a battery in the over - discharge condition, if vdd is greater than vrel2 and the vm is higher than vcha, the over - discharge condition is released. when a battery in the over - discharge condition, if vdd is greater than vdet2 and the vm is lower than v cha , the over - discharge condition is released. when the over - discharge condition hold, and the voltage difference between vm and vdd is less than 1.3v, the current consumption is reduced to the power - down current consumption 0.1ua in typical. in over - discharge condition, the vm pin is connected to vdd by internal pull - up resistor r vmd and the internal pull - down resistor r vms from vm pin to vss is disconnected. when the mosfet is off, vm pin voltage is pulled up by the resisto r to vdd in the ic, at this time, the power consumption is reduced to the lowest. this condition is called the green mode. over - current condition there are 3 kinds of over - current condition. one is the discharge over - current condition and another is the load short - circuiting condition and the other is charge over - current condition. the ec9526a monitors the vm pin voltage to detect the over - current and load short - circuiting condition. if vm pin voltage is greater than vdet3 and continues to discharge over - current delay time tvdet3, the over - current condition enabled and the do pin output logic l to disable the discharging path. at the same time, the discharging is stopped. in over - current condition, the internal pull - up resistor from vm pin to vdd r vmd is disconnected and the vm pin is connected to vss by internal pull - down resistor r vms . however, the vm pin is pull - up to vdd by external load resistor. when the load is disconnected, the vm pin is pull - down to vss by internal resistor. if the vm pin voltage falls below the charger detection voltage v cha under normal condition,and it continues and longer than the overcharge detection delay time tvdet1, the co pin will disable the charging path by disconnected the charge controlled mosfet. the charge over - curr ent detection is released when the voltage difference between vm pin and vss becomes less than charger detection voltage v cha .
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 8 of 10 4g25n rev. f001 ec 9526a timing diagram 1. over - charge voltage detection/release & over - discharge voltage detection / release
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 9 of 10 4g25n rev. f001 ec 9526a 2 . dis - charge over current detection & load short circuiting detection
one - cell lithium battery protection ic e - cmos corp. ( www.ecmos.com .tw ) page 10 of 10 4g25n rev. f001 ec 9526a package outline sot23 - 6l
|
